Autore Topic: Again problem with sticking  (Letto 1126 volte)

0 Utenti e 1 Visitatore stanno visualizzando questo topic.

Offline Parcival

  • Hero Member
  • *****
  • Karma: +3/-0
  • Sesso: Maschio
Again problem with sticking
« il: Maggio 20, 2014, 21:24:44 pm »
 :set2010069: The fitting of nib section can not be removed from the cap. Did not move. What it soak to move and I can pull it out. I think the water is not suitable for fitting.



Offline Wallygator

  • Special Guest
  • Hero Member
  • *********
  • Karma: +1/-0
  • Sesso: Maschio
Re:Again problem with sticking
« Risposta #1 il: Maggio 20, 2014, 23:23:37 pm »
Some minutes of warm hair dryer?

Offline Parcival

  • Hero Member
  • *****
  • Karma: +3/-0
  • Sesso: Maschio
Re:Again problem with sticking
« Risposta #2 il: Maggio 21, 2014, 08:44:41 am »
I think there sticking oxidation and ink - between the metal and hard rubber, I have not tried heat, but I guess should be cleaned with a liquid?

Offline Wallygator

  • Special Guest
  • Hero Member
  • *********
  • Karma: +1/-0
  • Sesso: Maschio
Re:Again problem with sticking
« Risposta #3 il: Maggio 21, 2014, 09:57:21 am »
I'm thinking about an Anti-rust  spray, or a silicone lubricant, but I dont know what are the effets to hard rubber of section.

Offline maxpen2012

  • Special Guest
  • Hero Member
  • *********
  • Karma: +0/-0
  • Sesso: Maschio
Re:Again problem with sticking
« Risposta #4 il: Maggio 21, 2014, 10:24:36 am »
Gentle ultrasonic wash in water and mild soap, may be?

Online Giuseppe Tubi

  • Top Expert
  • Hero Member
  • **********
  • Karma: +4/-0
  • Sesso: Maschio
Re:Again problem with sticking
« Risposta #5 il: Maggio 21, 2014, 11:53:07 am »
All the suggestions are right.
You can also try to beat gently on the external surface of the cap: sometimes the produced vibrations could unlock the inner part.

Offline maxpen2012

  • Special Guest
  • Hero Member
  • *********
  • Karma: +0/-0
  • Sesso: Maschio
Re:Again problem with sticking
« Risposta #6 il: Maggio 21, 2014, 12:27:34 pm »
All the suggestions are right.
You can also try to beat gently on the external surface of the cap: sometimes the produced vibrations could unlock the inner part.

Caro Tubi, il mio inglese ormai è esaurito con la faccenda dell'ultrasonic wash,
però ho sentito il mì nonno il quale mi ha suggerito un sistema empirico ma a volte efficace,
che consiste nell'usare uno di quei tasselli da muro ad espansione, meglio se fasciato con
un pò di nastro biadesivo, allargandolo con cautela a mano tramite la sua vite e tirando...
Quel vecchio demonio a volte mi sorprende ancora...   ;) :D 8)

Online Giuseppe Tubi

  • Top Expert
  • Hero Member
  • **********
  • Karma: +4/-0
  • Sesso: Maschio
Re:Again problem with sticking
« Risposta #7 il: Maggio 21, 2014, 14:10:00 pm »
All the suggestions are right.
You can also try to beat gently on the external surface of the cap: sometimes the produced vibrations could unlock the inner part.

Caro Tubi, il mio inglese ormai è esaurito con la faccenda dell'ultrasonic wash,
però ho sentito il mì nonno il quale mi ha suggerito un sistema empirico ma a volte efficace,
che consiste nell'usare uno di quei tasselli da muro ad espansione, meglio se fasciato con
un pò di nastro biadesivo, allargandolo con cautela a mano tramite la sua vite e tirando...
Quel vecchio demonio a volte mi sorprende ancora...   ;) :D 8)
Fai i complimenti al nonno: mi sembra un sistema davvero ingegnoso.

Offline Parcival

  • Hero Member
  • *****
  • Karma: +3/-0
  • Sesso: Maschio
Re:Again problem with sticking
« Risposta #8 il: Maggio 21, 2014, 19:42:21 pm »
This is a thin sheet. I tried to pull, but not moving.

Offline Giovanni Abrate

  • Top Expert
  • Hero Member
  • **********
  • Karma: +0/-0
  • Sesso: Maschio
Re:Again problem with sticking
« Risposta #9 il: Maggio 21, 2014, 23:36:59 pm »
Credo che l'unica sia il calore e tanta pazienza. Un heat gun termoregolata, cercando che il pezzo si riscaldi uniformemente.

Online Giuseppe Tubi

  • Top Expert
  • Hero Member
  • **********
  • Karma: +4/-0
  • Sesso: Maschio
Re:Again problem with sticking
« Risposta #10 il: Maggio 22, 2014, 18:03:36 pm »
I have a doubt: is the separation point on the red arrow or on the green one?

Tags:
 

       
Twittear